You get 1 pairs of tires.  Perfect replacement for dry-rotted Narrow chassis front tires.  

Size is .375" as measured mounted on a stock Tyco 440x2 narrow front rim.  

Size is .400" as measured mounted on a stock Tyco 440x2 Wide-Pan. This is lower than stock Wide-Pan tires. 

Can be run in certain applications on Wide-Pan chassis. Pickup shoe travel, magnets strength, track type may limit usage.

Chassis for display and NOT included.  

HCS AMG Silicone Slip-On Medium Compound

.454 OD  Black for Tyco 440x2

One pair of tires.  Sized for the standard factory .250 OD Tyco 440x2 rear rims.  If mounted on Viper .265 single flanged hubs, net size is approximately .464 OD.     

Pro-8 Traction Magnets for a great handling car with paired with these tires.  

They can be used on other rim configurations. Finished axle set and car are not included - for example only. 

HCS AMG Silicone Slip-On Medium Compound

.472 OD  Black for Tyco 440x2

One pair of tires.  Sized for the standard factory .250 OD Tyco 440x2 rear rims.  Pro-8  Pro-10 Traction Magnets for a great handling car with paired with these tires.   

They can be used on other rim configurations. Finished axle set and car are not included - for example only. 

Tyco 440 & HP-7 Standard Factory Aluminum Guide Pins

Five each steel pins.  Specifically for Tyco cars.  Light weight design. 

Tyco 440x2 Pro Quality CNC Machined Steel Guide Pins

Three each steel pins.  Specifically for Tyco 440x2 and similar cars.  CNC machined steel guide pins.  Fits most all Tyco HO slot cars.  

Pro quality design with large top and bottom flanges to eliminate guide pin shifting under load. 

Tyco 440 Standard Factory 7T Pinion Gear

Five each Nylatron 7T Pinion Gears.  Mate with Tyco crown gears as well as Viper, HCS AMG, RPMs Grey, Tomy, and BSRT crown gears.  Tyco pinion gears have a long history of high quality.  Over the years, many HOPRA championship racers have used the Tyco pinion in there Pro Ceramic Super Stock cars

  Viper Pro-10™ Traction Magnets for Tyco 440x2 Chassis

One pair of  magnets.  North / South oriented so they can be installed in either high downforce or low downforce (motor mode).  These are 'drop-in' for any Tyco 440x2 chassis or Mattel HPx2.  Magnets are marked red for the right side and white for the left side.  Installing them like this will be low downforce. 

These compression molded magnets are engineered for better fit and performance.  These magnets bring out the best in most factory stock cars. 

Viper Pro-4™ Motor Magnets for Tyco 440x2 and Mattel HPx2 Cars

One pair of magnets.  These are the real deal Level 4 compression molded motor magnets. Designed for a 'drop-in' fit for Tyco 440 and Mattel HPx2 cars.  Magnets have a 'hang down' flush fit design to allow better handling due to increased magnetism to the rails. 

Use with lower ohm armatures and Pro-8™ or Pro-10™ traction magnets for best setup.    

Viper Pro-4™ Motor Magnets for Tyco 440x2 and Mattel HPx2 Cars

One pair of magnets.  Level 8 grade compression molded magnets are 'Drop In Fit' for Tyco 440 based cars.  You get better performance in two ways: the magnets are very consistent and do not need to be gauss meter matched.  Secondly the magnets are flush with the bottom of the chassis to allow more magnetic attraction to the rails.  This helps keep the front end planted for better handling. 

Typical use with these motor magnets are in any class of car formula that calls for polymer magnets - generally factory based 3.5 ohm and lower armatures.

Ready to run car for example only.

Note: Cars built with Pro-8 Motor magnets and Pro-8 & Pro-10 Traction magnets will need to use the Tyco black stiff chassis. The gray nylon chassis will be too flexible. You will need to use better quality rear axle sets with pro quality gears from Viper, BSRT, Wizzard, or Slottech.  The Tyco factory gears will be too soft and fail quickly. 

Viper Pro-8™ Traction Magnets for Tyco 440x2 Chassis

One pair of  magnets.  North / South oriented so they can be installed in either high downforce or low downforce (motor mode).  These are 'drop-in' for any Tyco 440x2 chassis or Mattel HPx2.  Magnets are marked red for the right side and white for the left side.  Installing them like this will be low downforce. These compression molded magnets are engineered for better fit and performance.  

Tyco 440x2 Wide-Pan Hardbody Clip for Super 7, Viper V-1, BSRT G3, Tomy Super G Plus 

You've been asking for them - NOW you have them ! ! ! One each standard Tyco 440x2 Wide-Pan hardbody clip.  Brand New production run. 

These are the REAL DEAL engineered and injection molded parts.  Allows fitting most all Tyco 440x2 Wide-Pan bodies onto HCS Super 7, Tomy Super G Plus, BSRT G3, and Viper V1 without the lexan posts.

Not cheap MarkerBot 3D printed globs of 'starter kit' parts that don't fit well and have to be whittled on to work.       

Bodies and chassis NOT included - for display only. 

Viper O-Ring Front End Set for Tyco 440 Wide-Pan Chassis

You get one (1) complete axle set: Hubs, O-Rings, Axle.  Get your ride slammed for best handling!!   These are the real-deal CNC machined Delrin front 'o-ring' hubs and axle sets. 

These are designed to run in Tyco 440x2 & Mattel HPx2 Wide-Pan cars.  Other applications can be done with different size o-rings installed.  O-rings finish at .405 OD. For reference, factory Tyco / Mattel wide-pan fronts are .434 OD.

Sets shipped with hubs pressed on loose.  You may need press or other proper tools to get and exact fit to your specific car.  Chassis NOT included - for display only.

Vper O-Ring Front End Set for Tyco 440x2 Narrow and Tomy Mega-G, Mega-G+

You get one (1) complete axle set: Hubs, O-Rings, Axle.  Get your ride slammed for best handling!!   These are the real-deal CNC machined Delrin front 'o-ring' hubs and axle sets.  .

These are designed to run in Tyco 440x2 Narrow and Tomy Mega-G and Mega-G Plus.  Other applications can be done with different size o-rings installed.  Comes with 1 set of .360 o-rings to get your car 'slammed'!!

Sets shipped with hubs pressed on loose.  You may need press or other proper tools to get and exact fit to your specific car.  Chassis NOT included - for display only.